AP.setup is the default login address that is used to make login access for your New Extender Setup page. New Extender Setup using http://ap.setup or 192.168.10.1 IP address. Ap.setup dashboard gives you easy access to customize your Extender’s wireless settings. Access your Extender admin page or reset the password steps are available here.

You should get to http://ap.setup or 192.168.10.1 web-based utility for managing all advance settings for your New extender. After installing and making all configurations for your wireless extender, you will able to remove all dead zones from your home. You will get rapid web associations for you your development gadgets simply in the wake of making every single required setup for your gadget in an expert manner.

New Extender Setup Guide

Wireless range extenders assist you with boosting the quality of your current Wi-Fi signals. Simply perform new extender setup and appreciate continuous web access all through the home or office. Ap.setup plays a significant job in setting up the range extender. At the point when you interface the new extender and open a web program, it will automatically divert you to 192.168.10.1 IP address page. As a matter of fact that you are utilizing Apple gadgets like iPhone or iPad, use http://ap.setup web address to configure and setup your wireless range extenders with these gadgets. In some cases, the web program shows error messages when clients attempt to get to it. Ap.setup is not an internet website, it’s just a local web address to access the extender setup wizard.

New Extender Setup Modes

Currently, there are two setup modes are available for your extender. You can setup your range extender in two modes i.e Extender Mode or Repeater Mode and change the modes according to your desire.

Extender Mode

In this mode, your extender enhances the range of existing wireless network with no necessity for messy wired connections. After setup, you can remove with the dead zone in your home by enabling its Extender mode. If your router does have a WPS button, then you can interface it to the extender using a WPS button on extender similarly as a router.​

ap setup extender mode

Repeater Mode

In this mode, the extender will expand the Wi-Fi signals and eradicate all the connectivity issues. Keep your extender in Repeater mode in case you have to cover a vast area at your home or business. Go through with our website to know the setup instructions for New extender setup in repeater mode. Setup your extender easily with our guide.

New Extender Setup Using Ap.setup

Regardless of the way that the extender setup method is straightforward, customers still solicitation to perceive how it’s done. A wireless extender can be organized through two methodologies; you can pick any technique as necessities. These methods are explained below: 

  • WPS (WiFi Protected Setup) Method
  • Web-based Portal
ap-setup for extender

WPS Method

  1. Plug in the extender to the power source and wait for the power LED to be solid white.
  2. WPS button can be found on the front or side panel of the extender.
  3. Press and hold down the WPS button for about 5 seconds and when the LED light starts blinking on the extender, press the WPS button on the router as well.
  4. Now, log in to your router and check the IP address of the repeater in your router’s dashboard.
  5. Type the same IP address in the address bar of the browser and press enter.
  6. A login window will appear, enter the default username and password in the required fields.
  7. Now, click the setup wizard and select your existing wireless name from the list of the available wireless networks.
  8. You can also customize the SSID and the password for your extender on the same screen.
  9. Follow the instructions carefully to successfully setup your extender and place it after configuration where you’re getting less wireless signals.
  10.  

Web-Based Portal

  1. Turn on the extender and wait for the solid white power LED.
  2. Connect your extender to the PC or laptop via Ethernet cable or wireless.
  3. After making a connection, open a web browser in your computer and type ap.setup web address in the address bar of the browser and press enter.
  4. An extender web-based portal window will appear on your screen asking for the default credentials.
  5. Enter admin in both username and password field and click submit to login.
  6. Setup portal will scan your nearby wireless networks so, select the existing wireless network you want to extend.
  7. Next, enter the wireless network password for your existing router and ensure that the password is correct.
  8. You can likewise change the name of your extender’s wireless network.
  9. Click ‘Apply’ to save all the customized settings for your new extender.
  10. Connect your device with the new SSID of the extender and enjoy the services. Place the extender between the half of your router and the spot where you want the full Wi-Fi strength.
ap setup extender setup

How to setup New Extender in Repeater Mode?

Learn How to do a wireless extender setup in repeater mode, Firstly a quick intro about Repeater mode. It is a method in which you want to fill a big room or place with strong wireless signals. You’ll get the faster internet speed in the repeater mode.

  • Connect your PC or laptop to the extender’s wireless network.
  • Open the web browser on your computer and go to the ap.setup web address.
  • Fill in the default credentials for the extender to successfully login.
  • Next, you need to choose the repeater mode on the setup wizard of the extender.
  • Select your existing wireless network name and type in the password for your existing wireless.
  • You can likewise customize the SSID for the extender’s wireless.
  • Click on Apply to save all the customized settings for your extender.

How to setup New Extender in Extender Mode?

In this article, you will get the step by step procedure to setup in extender mode. If you want to extend your main wireless signals in a particular spot where you’re not getting the wireless signals from the main router, then extender mode is the best option for you.

  • Connect your computer and the extender via Ethernet cable.
  • Go to www.ap.setup address on the web browser. 
  • You can also use the 192.168.10.1 IP address to login to the setup portal of the extender.
  • Type in the default username and the password to log in to the setup portal of the extender.
  • Select the extender mode and it will scan for the nearby wireless networks.
  • Select your main wireless network and type in the password for your main Wi-Fi.
  • Click on apply to save the settings for your extender and you’re ready to use your extender now.

Fail To Access Ap.Setup Page?

Common Issues you might face to access the ap.setup page are listed below:

  1. Your device is not connected to the extender’s wireless network.
  2. Ap.setup web-based interface not responding.
  3. Browser Compatibility Issue.
  4. You don’t have any idea about the username and password to login.
  5. An Extender is not configured properly.

Solution: 

  1. Ensure that you’re connected to the extender either wireless or hardwired.
  2. Use the default IP address i.e 192.168.10.1 in case the ap.setup web address is not working.
  3. It doesn’t matter if you’ve internet or not, you can access the extender setup portal in offline mode also.
  4. You can see the default login credentials on the extender label or you can reset the extender to the default settings.
ap setup wifi extender setup

Can’t Access Extender Login Page After the Setup

An Extender is utilized when you need to expand the wireless signals in your home for your PCs and cell phones. Wireless range extender gadget needs to be configured using http://ap.setup page from your PC or a cell phone. When you need to change the settings for your device, you can use the extender login page for this. If you are getting problems with accessing your extender login page using the ap.setup page, here are the tricks you can try.

  • Use the IP address 192.168.10.1 instead of the ap.setup web address to log in to the extender portal.
  • Use the updated web browser to access the extender login page.
  • Connect your extender and your computer via Ethernet cable and then try to access the extender login page.
  •  At last, you can reset your extender and after that, you would be able to login to the extender.

How to Reset the Extender?

There are two methods available to reset the extender. As I’ve also tried these two methods to reset the extender and got the success in the first attempt. You can also try these two methods to successfully reset the extender to the default settings.

Method 1:

What I did was first disconnect the extender from the power source for a few seconds, plug it back in then hold the reset button down for about 10-15 seconds before your computer registers the connection is there and tries to connect. you will have a 15-20 seconds gap to start this process. It should then revert to its default factory name and bring you to the extender setup interface after you enter your credentials.

Method 2:

When your device is connected to the extender’s network, go to the web-based interface of the extender, by typing in http://ap.setup or 192.168.10.1 IP address in your web browser. It should ask you to enter the credentials and bring you to a summary page that shows the info and status of your network. Go to the advanced settings and there should be an option to reset. If it doesn’t work or you cannot access the web menu make sure you’re using an Ethernet cable to connect the extender to the computer.

Check the status of the LED lights on the Extender

  • Power LED: When you plug the extender to a power source then this power LED light lit up.
  • Ethernet port: The Ethernet port LED lit up when you connect the device with the extender through Ethernet cable.
  • Internet LED: When your extender is connected to the router and receiving internet connection then the LED light will stable.
  • Wi-Fi LED: when the internet packets are transmitted or received on a wireless device through the extender then this LED lit up.
  • WPS (Wi-Fi Protected Setup): When WPS setup is enabled then the light flickers.

What are the most common issues while login and set up the new extender and how to fix it?

The most widely recognized issues faced by clients is the initial extender setup. The issues happen because of connectivity issues, IP address, internet browser and so on. Here are some normal issues which our specific specialists can assist you with settling in a matter of seconds:

  • Connectivity Problems
  • Static IP address
  • MAC address not found
  • Not able to login to the extender
  • Ap.setup page can’t be displayed
  • Server not found
  • Router password is incorrect
  • Unexpected 404 error
  • Unable to login with a default password
  • Not able to connect devices with extender’s network
  • No internet when connected to the extender
  • IP confliction
  • Intermittent wireless connection
  • Mismatched wireless settings

There can be many reasons that you’re facing these issues to setup your extender. Follow the steps to eradicate these and setup your extender successfully.

  1. Ensure that your router and the extender is powered on.
  2. Connect your extender to the devices via Ethernet cable.
  3. Type ap.setup web address in the URL bar of the browser and press enter.
  4. In any case, the web address doesn’t seem to work, try 192.168.10.1 IP address to access the setup page.
  5. Fill in the default credentials for the extender to log in to setup portal of the extender.
  6. Once you’re logged in, it will scan for the available wireless networks.
  7. Select your wireless network name and enter the correct password for your existing wireless carefully.
  8. Follow the rest of the instructions and then you’re ready to use your extender.

Wi-fi Extender Setup Help

Close Menu